Using lower-case filename for host-setup documentation.

Signed-off-by: Daniel Baumann <daniel.baumann@open-infrastructure.net>

1 files changed, 0 insertions, 230 deletions

diff --git a/share/doc/HOST-SETUP.txt b/share/doc/HOST-SETUP.txt
deleted file mode 100644
index 8cb6039..0000000
--- a/share/doc/HOST-SETUP.txt
+++ /dev/null
@@ -1,230 +0,0 @@
-compute-tools: Host Setup
-=========================
-
-
-1. Debian Packages
--------------------
-
-apt install bridge-utils ifenslave vlan
-
-
-2. Boot Parameters
-------------------
-
-2.1 CGroup Memory Controller
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-In order to enable the memory controller the following boot parameter needs to be used:
-
-	cgroup_enable=memory
-
-
-2.2 CGroup Swap Controller
-~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-In order to enable the swap controller the following boot parameter needs to be used:
-
-	swapaccount=1
-
-2.3 vsyscall
-~~~~~~~~~~~~
-
-In order to be able to execute binaries linked to older libc versions
-(<= wheezy) on newer linux versions (>= buster), add the following boot
-parameter (see #881813 for more information):
-
-	vsyscall=emulate
-
-
-3. Networking
-~~~~~~~~~~~~~
-
-3.1 Configure Network Bridge
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-3.1.1 Bridge: 1 Interface, standalone, DHCP
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-cat > /etc/network/interfaces << EOF
-# /etc/network/interfaces
-
-source /etc/network/interfaces.d/*
-
-auto lo
-iface lo inet loopback
-
-iface eno1 inet manual
-
-auto bridge0
-iface bridge0 inet dhcp
-	bridge_ports	eno1
-	bridge_fd	0
-	bridge_maxwait	0
-	bridge_stp	0
-EOF
-
-
-3.1.2 Bridge: 1 Interface, standalone, static
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-cat > /etc/network/interfaces << EOF
-# /etc/network/interfaces
-
-source /etc/network/interfaces.d/*
-
-auto lo
-iface lo inet loopback
-
-iface eno1 inet manual
-
-auto bridge0
-iface bridge0 inet static
-	address		10.0.0.2
-	gateway		10.0.0.1
-	netmask		24
-
-	pre-up		ip link set eno1 down
-	pre-up		ip link set eno1 up
-
-	bridge_ports	eno1
-	bridge_fd	0
-	bridge_maxwait	0
-	bridge_stp	0
-EOF
-
-
-3.1.3 Bridge: 2 logical Interfaces, subnet, static
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-cat > /etc/network/interfaces << EOF
-# /etc/network/interfaces
-
-source /etc/network/interfaces.d/*
-
-auto lo
-iface lo inet loopback
-
-allow-hotplug eno1
-iface eno1 inet dhcp
-
-auto bridge0
-iface bridge0 inet static
-	address		10.0.0.1
-	netmask		24
-
-	pre-up		ip link add name bridge0 type bridge
-	post-down	ip link delete bridge0 type bridge
-
-	bridge_fd	0
-	bridge_maxwait	0
-	bridge_stp	0
-EOF
-
-
-3.1.4 Bridge: 3 physical Interfaces, vlan, bonding, static
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-cat > /etc/network/interfaces << EOF
-# /etc/network/interfaces
-
-source /etc/network/interfaces.d/*
-
-auto lo
-iface lo inet loopback
-
-allow-hotplug eno1
-iface eno1 inet dhcp
-
-iface eno2 inet manual
-
-iface eno3 inet manual
-
-auto bond0
-iface bond0 inet manual
-	up			ip link set bond0 up
-	down			ip link set bond0 down
-
-	slaves			eno2 eno3
-
-	bond-mode		4
-	bond-miimon		100
-	bond-downdelay		200
-	bond-updelay		200
-	bond-lacp-rate		1
-	bond-xmit-hash-policy	layer2+3
-
-iface bond0.100 inet manual
-	vlan-raw-device bond0
-
-auto bridge-100
-iface bridge-100 inet static
-	address			10.100.0.2
-	netmask			24
-
-	bridge_ports		bond0.100
-	bridge_fd		0
-	bridge_maxwait		0
-	bridge_stp		0
-EOF
-
-
-4. Enabling user namespace for unprivileged containers
-------------------------------------------------------
-
-Linux supports unprivileged containers with the user namespace.
-By default the user namespace is disabled on Debian systems (see #898446).
-To enable user namespace, edit the following file for a permant change:
-
-  /etc/sysctl.d/zz-compute-tools.conf
-  sysctl -p
-
-or enable it manually with:
-
-  echo 1 > /proc/sys/kernel/unprivileged_userns_clone
-
-Note that containers need to be started with the correct
-configuration in /etc/compute-tools/container/config to run unpriviled
-(private-users option).
-
-
-5. Enabling container-shell
----------------------------
-
-Managing privileged containers requires root privileges. In order to allow
-unprivileged users to manage privileged containers without granting them
-privileges or accounts, the container-shell can be used together with sudo
-and a container user.
-
-  sudo adduser --gecos "compute-tools,,," \
-	--home /var/lib/open-infrastructure/container-shell \
-	--shell /usr/bin/container-shell
-
-
-6. IPv4 and IPv6 dual-stack
----------------------------
-
-Examples for /etc/network/interfaces above work for IPv6 too when using correct
-IPv6 addresses and netmasks.
-
-In order to use dual-stack, bridges must have a IPv4 address assigned
-(can be a dummy one from a privacy range or 127.0.0.0/8).
-
-Let me repeat: dual-stack only works when you assign a primary IPv6 address
-(private or public, doesn't matter) *and* add an additional IPv4 address.
-Yes, the IPv4 address can be a private address, the containers can still
-have a public IPv4 address.
-
-A complete example looks like this:
-
-auto bridge0
-iface bridge0 inet6 static
-	address			2a07:6b47:4::4:1
-	netmask			48
-
-	up			ip addr add 127.4.4.1 dev $IFACE
-	down			ip addr del 127.4.4.1 dev $IFACE
-
-	bridge_fd		0
-	bridge_maxwait		0
-	bridge_stp		0
-	bridge-mcquerier	1